Flux Modulated Rotating Pole Piece Magnetic Gear

Mohd Firdaus Mohd Ab Halim

Abstract


In this paper, the CMG is re-condition so that the pole piece act as the outer rotor instead of surface mount PM. This magnetic coupling of the CMG is similar to the conventional CMG which uses harmonic to transfer the torque and speed from the inner rotor to the outer rotor. The working principle of the proposed CMG is derived analytically and simulated using finite element software. For this recondition, the PM at the outer section become stationary hence, retaining sleeve can be remove. The proposed MG produced 18% higher average torque than the conventional MG with drawback in torque ripple. The proposed CMG also produce higher gear ratio than the same pole pair of conventional CMG.

References


J. Larminie and J. Lowry, Electric Vehicle Technology Explained: Second Edition. 2012.

D. Fodorean, F.Jurca, M.Ruba, and D. C. Popa, “Motorization Variants for Light Electric Vehicles. design, magnetic, mechanical and thermal aspects,” in AlmaMater, 2013.

J. De Santiago et al., “Electrical motor drivelines in commercial all-electric vehicles: A review,” IEEE Trans. Veh. Technol., 2012.

I. Husain, “Electric and Hybrid Vehicles: Design Fundamentals, Second Edition,” Amazon, 2010.

D. Fodorean, “Study of a high-speed motorization with improved performances dedicated for an electric vehicle,” IEEE Trans. Magn., 2014.

F. Luise et al., “Design and technology solutions for high-efficiency high-speed motors,” in Proceedings - 2012 20th International Conference on Electrical Machines, ICEM 2012, 2012.

A. Tenconi, S. Vaschetto, and A. Vigliani, “Electrical machines for high-speed applications: Design considerations and tradeoffs,” IEEE Trans. Ind. Electron., 2014.

G. Pellegrino, A. Vagati, B. Boazzo, and P. Guglielmi, “Comparison of induction and PM synchronous motor drives for EV application including design examples,” IEEE Trans. Ind. Appl., 2012.

D. Gerada, A. Mebarki, N. L. Brown, K. J. Bradley, and C. Gerada, “Design aspects of high-speed high-power-density laminated-rotor induction machines,” IEEE Trans. Ind. Electron., 2011.

S. Il Kim, Y. K. Kim, G. H. Lee, and J. P. Hong, “A novel rotor configuration and experimental verification of interior pm synchronous motor for high-speed applications,” in IEEE Transactions on Magnetics, 2012.

D. P. Marčetić, I. R. Krčmar, M. A. Gecić, and P. R. Matić, “Discrete rotor flux and speed estimators for high-speed shaft-sensorless im Drives,” IEEE Trans. Ind. Electron., 2014.

R. R. Moghaddam, F. Magnussen, and C. Sadarangani, “Theoretical and experimental reevaluation of synchronous reluctance machine,” IEEE Trans. Ind. Electron., 2010.

J. H. Seo, T. K. Chung, C. G. Lee, S. Y. Jung, and H. K. Jung, “Harmonic iron loss analysis of electrical machines for high-speed operation considering driving condition,” in IEEE Transactions on Magnetics, 2009.

D. Fodorean, “State of the Art of Magnetic Gears, their Design, and Characteristics with Respect to EV Application,” in Modeling and Simulation for Electric Vehicle Applications, Mohamed Amine Fakhfakh, IntechOpen, 2016.

D. E. Hesmondhalgh and D. Tipping, “A multielement magnetic gear,” IEE Proc. B Electr. Power Appl., 1980.

K. Tsurumoto and S. Kikuchi, “A new magnetic gear using permanent magnet,” IEEE Trans. Magn., 1987.

C. G. C. Neves, D. L. Figueiredo, and A. S. Nunes, “Magnetic Gear : A Review,” 2014 11th IEEE/IAS Int. Conf. Ind. Appl., pp. 1–6, 2014.

K. A. and D. Howe, “A novel high-performance linear magnetic gear,” IEEE Trans. Magn., vol. 37, no. 4, pp. 2844–2846, 2001.

S. D. C. and D. H. K. Atallah, “Design, analysis and realisation of a high- performance magnetic gear,” IEE Proceedings-Electric Power Appl., vol. 150, no. 2, pp. 139–145, 2004.

X. Li, K. T. Chau, M. Cheng, and W. Hua, “Comparison of magnetic-geared permanent-magnet machines,” Prog. Electromagn. Res., vol. 133, no. August 2012, pp. 177–198, 2012.

X. Zhang, X. Liu, C. Wang, and Z. Chen, “Analysis and Design Optimization of a Coaxial Surface-Mounted Permanent-Magnet Magnetic Gear,” pp. 8535–8553, 2014.

C. S. Gim, E. J. Park, S. Y. Jung, and Y. J. Kim, “Torque Characteristic Analysis of Coaxial Magnetic Gear According to Fillet Parameter of Pole Piece,” ICEMS 2018 - 2018 21st Int. Conf. Electr. Mach. Syst., no. 1, pp. 2557–2560, 2018.

H. Kong and U. States, “A New Coaxial Magnetic Gear Using Stationary Permanent Magnet Ring,” pp. 634–638, 2013.

J. X. Shen, H. Y. Li, H. Hao, M. J. Jin, and Y. C. Wang, “Topologies and performance study of a variety of coaxial magnetic gears,” IET Electr. Power Appl., vol. 11, no. 7, pp. 1160–1168, 2017.

K. Aiso, K. Akatsu, and Y. Aoyama, “Reluctance magnetic gear and flux switching magnetic gear for high speed motor system,” 2017 IEEE Energy Convers. Congr. Expo. ECCE 2017, vol. 2017-Janua, pp. 2445–2452, 2017.

E. Park, C. Gim, S. Jung, and Y. Kim, “A gear efficiency improvement in magnetic gear by eddy-current loss reduction,” Int. J. Appl. Electromagn. Mech., vol. 1, pp. 1–10, 2018.

B. McGilton, R. Crozier, and M. Mueller, “Optimisation procedure for designing a magnetic gear,” J. Eng., vol. 2017, no. 13, pp. 840–843, 2017.

C. C. Huang, M. C. Tsai, D. G. Dorrell, and B. J. Lin, “Development of a magnetic planetary gearbox,” IEEE Trans. Magn., vol. 44, no. 3, pp. 403–412, 2008.

J. L. Perez-Diaz, E. Diez-Jimenez, M. A. Alvarez-Valenzuela, J. Sanchez-García-Casarrubios, C. Cristache, and I. Valiente-Blanco, “Magnetic Gearboxes for Aerospace Applications,” Aerosp. Mech. Symp., pp. 365–374, 2014.

S. Kim, E. Park, and Y. Kim, “Optimal Design of Ferromagnetic Pole Pieces for Transmission Torque Ripple Reduction in a Magnetic-Geared Machine,” J. Electr. Eng. Technol., vol. 11, no. 6, pp. 1628–1633, 2016.

J. Corporation, “JMAG Application Note 207.” pp. 1–16, 2015.

J. Dong, Y. Huang, L. Jin, and H. Lin, “Comparative Study of Surface-Mounted and Interior Permanent-Magnet Motors for High-Speed Applications,” IEEE Trans. Appl. Supercond., vol. 26, no. 4, pp. 26–29, 2016.

L. Chen and C. Zhu, “Strength Analysis for Surface-mounted Permanent Magnet Rotor in High-Speed Motor,” TELKOMNIKA Indones. J. Electr. Eng., vol. 12, no. 10, 2014.

E. I. Mbadiwe and E. Sulaiman, “Improved design of outer rotor machine in PM technology for motor bike drive application,” in ISCAIE 2018 - 2018 IEEE Symposium on Computer Applications and Industrial Electronics, 2018.

M. F. Omar, E. Sulaiman, H. A. Soomro, F. Amin, L. I. Jusoh, and E. I. Mbadiwe, “Optimal design of single-phase 12S-6P FEFSM using segmental rotor and non-overlap windings,” Indones. J. Electr. Eng. Comput. Sci., vol. 14, no. 2, pp. 735–743, 2019.




DOI: http://doi.org/10.11591/ijpeds.v11.i4.pp%25p
Total views : 27 times

Refbacks

  • There are currently no refbacks.


Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.